問題描述：你留的這個是QQ吧。已經發到你的QQ郵箱了。

回答(1).so the conveyor belt is in tension statebe screwed, so the conveyor belt in tension state. The machine before the use of adjusted the conveyor belt ( station in a first direction of paper, at the same time release on both sides of the handle, the pine to the conveying belt. Then tighten the right handle, left immobiles. Until the conveyor belt move, then two quarter circle, basic took place. Such deviation after rectifying roller can play a role, while not against bad belt ). Starting half an hour later, confirm the conveyor belt will not always deviation, in order to properly use the machine, otherwise the resulting conveyor belt damage by the users responsibility! Open the pump switch, working after two minutes. Pull cover observed liquid outlet has no coating (coating ) liquid outflow. A. The regulation of steel rods make close contact roller ( rubber cot ), to be the film liquid normal outflow after a minute to open the main motor switch, when the film liquid coated with cots, to start the normal film. The film to open the B. UV curing machine conveyor motor and the UV switch, and then the paper first leveled put into the board, hands flat advance paper. Standby device automatically into the film will begin after normal film. Attention: (But the rubber roll and enters between the paper steel roller to be best contacts completely also may have crevice to have to be smaller than paper thickness), between the rubber roll and the adjustment steel roller the close contact ......

回答(2).你是下麵的那個屏壞了咯？ 這樣的話，就好辦了. 你在往下下一本台達VFD-M的變頻器說明書，將參數p00 和p01給成麵板控製。 這樣你就可以通過第一張圖上那個綠色的鍵啟動變頻器（傳輸帶）用紅色的鍵停止。用那個可以旋轉的電位器控製速度。 當然這些前提是你要是下麵的那個屏還有其他的作用的話，變頻器是實現不了的，

回答(3).8. When shutdown (such as steel roller and feed rollers are Keys to use) then turn off the pump switch, a few minutes later, when there is no lamination roller liquid has to stop. And release the roller and all Contact pressure between steel rollers. Special Note: do not adjust the machine must be released between the steel roller and pressure roller, steel roller, and if the feed roller contacts together. but also to rise up roller, rubber roller to avoid unilateral time pressure deformation! 9.UV lights five minutes after the switch is turned to work properly. UV light is off after the five minutes to open, start the first open UV light, and then open the cooling fan. UV cooling fan and will be transferred to such a weak UV lamp to light up within minutes. Up until after the UV light and then transferred to the cooling fan slightly stronger UV. (To adjust the temperature according to the specific size, but best not to be transferred to the strongest at UV cooling fan, fan life so as not to affect long-term use) every day as Laminating together. Sticky film phenomenon occurs when the eject must be timely, so as not to roll in the machine can not be removed. 10.If for a long time or do not have dust, impurities, when required anhydrous alcohol and white silk cleaning roller and adjustable steel roller surface. 11. And to release the adjusted steel rollers and roller does not make close contact. Note to adjust the cleaning roller steel roller to leave, do not let the s......

回答(4).As the process of moving conveyor belt tension screw may twist the handle, so the belt is tight state machine must be adjusted before use conveyor belt (the direction of the paper stand out, while the first release on both sides of the handle, loose to belt slip can then tighten the right side of the handle, the left does not move until the belt dynamic, and more-half circle, basically pulled in place, so that after deviation correction roller to work, while not arrived bad tape). start a half hour later, make sure belt does not have deviation in order to properly use the machine, conveyor belt or damage resulting from the user's responsibility! Open the pump switch, work two minutes later. （coating） Lift the top cover mouth with or without lamination observed liquid (coating) fluid flow. a. adjust the regulator to make close contact with steel rod roller (rubber cot), the normal outflow of fluid to be laminating a minute to open the main electrical switch, when the lamination roller liquid painted, you can start the normal lamination. b. when you first open the laminating machine UV curing and UV conveyor motor switch, and then flat on the paper into the cardboard on the front, his hands flat to promote the paper. Automatic film advance until the machine after a normal lamination. Note: The steel roller and paper feed roller all the contacts between the best (but may also have gaps smaller than the thickness of the paper), rubber rollers and adjustable steel rollers clos......

本文章由水蜜桃性爱激情网站廠家整理原創，轉載請注明出處：http://www.rfxfamily.com/UVj/3867.html